Tel: 00353 402 32116
Your basket is empty
SprayWriter Forest H 37023511 Whi*
18MM581
Ex VAT 5.31 EACH
Spray Writer 370235 Forestry & Plantation Marking Paint - 350g
Dy-Mark’s Spray Writer is a reduced toxicity spray for all natural and cut timber applications. With reduced spray drift and low odour this convenient 360° marker is ideal for the forestry and timber processing industries. Spray Writer is also suitable for use in the construction industry.
The product has been formulated to mark wet surfaces without cracking or flaking.
* Toluene-free formula
* Ideal for all natural and cut timber applications
* Will mark wet surfaces without cracking and peeling
* Unique formulation reduces spray drift allowing maximum accuracy of spray pattern
* Ideal for the forestry and timber processing industries
* Also suitable for marking masonry and concrete
Preparation
Shake can for at least 20 seconds after the mixing ball begins to rattle.
Application
Hold can upright or in the inverted position and spray with the nozzle 15 – 20cm from the surface. Adjust the spray pattern by moving closer or further away from surface to be sprayed.
TECHNICAL DATA
Size: 350g Aerosol
Finish: Matt
Colour: 8 Standard and 7 Fluoro Colours
Consistency: Liquid
Coverage: Approximately 2 sqm per can (depending on the surface)
Suitable Surfaces: Natural and cut timber, concrete, masonry, bitumen
Drying Time: 10 minutes at 25°C
Temperature: Between 5°C and 40°C
STORAGE
Store below 50°C. Do not store in direct sunlight or in vehicles under hot conditions. Protect aerosol cans against physical damage.
DISPOSAL
Aerosol should be completely emptied prior to disposal. Contents of can are under pressure. Do not puncture or incinerate even when empty. When empty, dispose of this container through an approved recycling scheme or seek advice from your local council regarding accepted disposal methods.
SAFETY INFORMATION
HIGHLY FLAMMABLE
Keep away from flame, heat and sources of ignition. Do not smoke and ensure adequate ventilation during use. Can be harmful by inhalation, in contact with skin and if swallowed. Intentional misuse by deliberately inhaling contents can be harmful or fatal. Please note that the slip resistance and performance of this product depends on many factors outside the control of Dy-Mark; including surface preparation, correct application and environmental conditions. Dy-Mark recommends a risk assessment prior to use to determine if the product is suitable to the:
* Slip resistance required
* Surface type
* Volume of traffic
* Potential exposure to any surface contaminants e.g. water, solvents or chemicals
KEEP AWAY FROM CHILDREN
Dy-Mark’s Spray Writer is a reduced toxicity spray for all natural and cut timber applications. With reduced spray drift and low odour this convenient 360° marker is ideal for the forestry and timber processing industries. Spray Writer is also suitable for use in the construction industry.
The product has been formulated to mark wet surfaces without cracking or flaking.
* Toluene-free formula
* Ideal for all natural and cut timber applications
* Will mark wet surfaces without cracking and peeling
* Unique formulation reduces spray drift allowing maximum accuracy of spray pattern
* Ideal for the forestry and timber processing industries
* Also suitable for marking masonry and concrete
Preparation
Shake can for at least 20 seconds after the mixing ball begins to rattle.
Application
Hold can upright or in the inverted position and spray with the nozzle 15 – 20cm from the surface. Adjust the spray pattern by moving closer or further away from surface to be sprayed.
TECHNICAL DATA
Size: 350g Aerosol
Finish: Matt
Colour: 8 Standard and 7 Fluoro Colours
Consistency: Liquid
Coverage: Approximately 2 sqm per can (depending on the surface)
Suitable Surfaces: Natural and cut timber, concrete, masonry, bitumen
Drying Time: 10 minutes at 25°C
Temperature: Between 5°C and 40°C
STORAGE
Store below 50°C. Do not store in direct sunlight or in vehicles under hot conditions. Protect aerosol cans against physical damage.
DISPOSAL
Aerosol should be completely emptied prior to disposal. Contents of can are under pressure. Do not puncture or incinerate even when empty. When empty, dispose of this container through an approved recycling scheme or seek advice from your local council regarding accepted disposal methods.
SAFETY INFORMATION
HIGHLY FLAMMABLE
Keep away from flame, heat and sources of ignition. Do not smoke and ensure adequate ventilation during use. Can be harmful by inhalation, in contact with skin and if swallowed. Intentional misuse by deliberately inhaling contents can be harmful or fatal. Please note that the slip resistance and performance of this product depends on many factors outside the control of Dy-Mark; including surface preparation, correct application and environmental conditions. Dy-Mark recommends a risk assessment prior to use to determine if the product is suitable to the:
* Slip resistance required
* Surface type
* Volume of traffic
* Potential exposure to any surface contaminants e.g. water, solvents or chemicals
KEEP AWAY FROM CHILDREN
News & Promotions
By Niall Kelly on Thu 12 October 2023
Testimonials